Dfsmsrmm not active. Jun 6, 2024 · Why does using the TI command from ISPF 3.

Dfsmsrmm not active. Jun 6, 2024 · Why does using the TI command from ISPF 3. SVC FLAGS = flags EDG0101I STARTED TASK ENDED BECAUSE THE DFSMSrmm SUBSYSTEM IS ALREADY ACTIVE EDG0102E STARTED TASK ENDED BECAUSE THE DFSMSrmm SUBSYSTEM IS NOT DEFINED AS A SUBSYSTEM EDG0103D DFSMSrmm SUBSYSTEM INTERFACE IS INACTIVE - ENTER "IGNORE", "CANCEL" OR "RETRY" EDG0104E DFSMSrmm SUBSYSTEM DFSMSrmm SUBSYSTEM NOT ACTIVE DURING function PROCESSING FOR volser - ENTER "RETRY", "IGNORE", OR "CANCEL" EDG0011E DFSMSrmm CANNOT RECORD TAPE VOLUME I/O ERRORS - INITIALIZATION CONTINUES. EDG0105I DFSMSrmm SUBSYSTEM INITIALIZATION COMPLETE If the subsystem inter f ace was not acti vat ed bef ore the command, you see the f ollowing message: EDG0103D DFSMSrmm SUBSYSTEM INTERFACE IS IN ACTIVE - ENTER "IGNORE", "CANCEL" OR "RETRY" EDG0011E DFSMSrmm CANNOT RECORD TAPE VOLUME I/O ERRORS - INITIALIZATION CONTINUES. I replied IGNORE and job ended succesfully (RC=0, datasets restored). The subsystem is inactive, and the operator replied CANCEL to the message EDG8102D. If the control data set is being restored from tape, reply IGNORE to allow tape processing to continue with a non-system managed tape drive. Use EDGHSKP to back up both the control data set and the journal when the DFSMSrmm subsystem is active by specifying the BACKUP DD statement and the JRNLBKUP DD statement. The operator can also use the abbreviations of QUERY and ACTIVE: F DFRMM,Q ACT or F DFRMM,Q A. I've got several RMM messages: EDG8102D DFSMSrmm SUBSYSTEM NOT ACTIVE DURING function PROCESSING FOR volser - ENTER "RETRY", "IGNORE", OR "CANCEL" volser names in the message body was SMS-managed volsers where the datasets resided before it were dumped. In other words: If the operator enters CONTINUE during CLOSE processing, DFSMSrmm allows the CLOSE to complete. The information in the control data set might not be correct if the CLOSE completes. If you want to run tape processing without DFSMSrmm being active, use the DFSMSrmm EDGRESET utility to remove DFSMSrmm from the system and then reply RETRY. SVC FLAGS = flags EDG0101I STARTED TASK ENDED BECAUSE THE DFSMSrmm SUBSYSTEM IS ALREADY ACTIVE EDG0102E STARTED TASK ENDED BECAUSE THE DFSMSrmm SUBSYSTEM IS NOT DEFINED AS A SUBSYSTEM EDG0103D DFSMSrmm SUBSYSTEM INTERFACE IS INACTIVE - ENTER "IGNORE", "CANCEL" OR "RETRY" EDG0104E DFSMSrmm SUBSYSTEM EDG8119Ifunction OF VOLUME volser REFUSED - DFSMSrmm NOT ACTIVE Explanation EDGLCSUX or EDGOCEXT was called to process the volume volser. If DFSMSrmm does not start, inform systems support personnel. DFSMSrmm subsystem interface processing now correctly detects that DFRMM is or has been stopped Fails incomplete and unprocessed requests for the reason ‘DFSMSrmm is not active’ F DFRMM,QUERY ACTIVE operator command from an operator console at any time to display the status of DFSMSrmm, its local tasks, and request queues. This processing requires that the DFSMSrmm subsystem is active. Explanation EDGLCSUX or EDGOCEXT was called to process the volume volser. EDG8119Ifunction OF VOLUME volser REFUSED - DFSMSrmm NOT ACTIVE Explanation EDGLCSUX or EDGOCEXT was called to process the volume volser. 4 "DSLIST" a message is given "DFSMSrmm not active". . lo jugat rqy x6dh0 oxs gx1rc x6 cxawy t8 5ryf6